Guidance
‘Pre-Exit’ European Assessment Documents: construction products
Notices of publication and a consolidated list of references of pre-Exit European Assessment Documents for construction products.
Applies to England, Scotland and Wales
Notices of publication from the Department for Levelling Up, Housing and Communities are provided for ‘pre-Exit’ European Assessment Documents (EADs) for construction products. This supports Regulation 305/2011, as amended by the Construction Products (Amendment etc) (EU Exit) Regulations 2019.
A pre-Exit EAD means:
a) A European Assessment Document for which
i. A reference was published in the Official Journal of the European Union under Article 22 as it had effect immediately before 31 December 2020; and
ii. The reference was not removed from publication before 31 December 2020; or
b) Guidelines published before 1 July 2013 under Article 11 of Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products which, immediately before 31 December 2020, could be used for the purposes of issuing European Technical Assessments under this Regulation. These guidelines are referred to as European Technical Approval Guidelines (ETAGs).
These pre-Exit EADs, together with the relevant horizontal standards on assessment methods, allow for UK approved bodies to produce UK Technical Assessments (UKTAs).
The following list of pre-Exit EADs will be kept up to date to include references to the versions adopted by UK Technical Assessment Bodies (TABs).
European Assessment Documents
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 010001-00-0301 | Precast concrete composite wall with point connectors | 2016/C 248/06 |
| 010003-00-0301 | Precast balcony elements made of Ultra High Performance Fibre Reinforced Concrete (UHPFRC) | 2018/C 019/04 |
| 010013-00-0301 | Lightweight panel made of mortar of cement and granulated EPS reinforced by a glass fibre mesh and an internal steel railing | 2018/C 019/04 |
| 010028-00-0103 | Shallow and reusable foundation kit for lightweight structures | 2018/C 228/03 |
| 020001-01-0405 | Multi-axis concealed hinge assemblies | 2017/C 118/04 |
| 020002-00-0404 | Balcony and terrace glazing system without vertical frames | 2016/C 054/14 |
| 020011-00-0405 | Roof, floor, wall and ceiling hatches providing access or for use as an emergency door/with or without fire resistance | 2016/C 248/06 |
| 020029-00-1102 | Internal pedestrian fire resisting and/or smoke control single or double leaf doorsets made of steel | 2017/C 343/06 |
| 030019-00-0402 | Liquid applied roof waterproofing on the basis of polysiloxane | 2017/C 118/04 |
| 030065-00-0402 | Composite roof waterproofing kit | 2018/C 228/03 |
| 030092-00-0605 | Mineral non-flexible sealing slurry kit on the basis of cement | 2018/C 370/05 |
| 030155-00-0402 | One component bitumen-polyurethane resin for flashing application | 2018/C 417/07 |
| 030218-00-0402 | Membrane for use as roof underlay | 2017/C 379/07 |
| 030219-00-0501 | Acoustic spray coating based on a water-based organic binder | Decision (EU) 2020/1574 |
| 030350-00-0402 | Liquid applied roof waterproofing kits | Decision (EU) 2020/1574 |
| 030351-00-0402 | Systems of Mechanically Fastened Flexible Roof Waterproofing Sheets | Decision (EU) 2019/896 |
| 030352-00-0503 | Liquid applied watertight covering kits for wet room floors and/or walls | Decision (EU) 2020/1574 |
| 030378-00-0605 Previously referred as 030378-01-0605 |
Fully bonded, pre-applied flexible sheet for waterproofing | Decision (EU) 2020/1574 |
| 030400-00-0605 | Waterproofing kit based on polymeric membranes for in- and outdoor walls and floors of wet areas and swimming pools | Decision (EU) 2020/962 |
| 030436-00-0503 | Watertight covering kits based on flexible sheets for wet room floors and/or walls | Decision (EU) 2020/1574 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 030437-00-0503 | Watertight covering kits based on inherently watertight boards for wet room floors and/or walls | Decision (EU) 2020/1574 |
| 040005-00-1201 | Factory-made thermal and/or acoustic insulation products made of vegetable or animal fibres | 2016/C 054/14 |
| 040007-00-1201 | Thermal insulation products for buildings with radiant heat reflective component | 2017/C 435/07 |
| 040010-00-1201 | Insulation product made of expanded perlite (EPB) | 2018/C 090/04 |
| 040011-00-1201 | Vacuum insulation panels (VIP) with factory applied protection layers | 2018/C 019/04 |
| 040012-00-1201 | Thermal insulation board made of mineral material | 2018/C 281/04 |
| 040037-00-1201 | Low lambda composite boards made of mineral wool fibres and aerogel additives | 2017/C 118/04 |
| 040048-01-0502 | Rubber fibre mat to be used for impact sound insulation | 2018/C 228/03 |
| 040049-00-0502 | Polyurethane (PU) foam mat to be used for impact sound insulation | 2018/C 228/03 |
| 040057-00-1201 | Thermal insulation board made of microporous silica | 2018/C 228/03 |
| 040065-00-1201 | Thermal insulation an/or sound absorbing boards based on expanded polystyrene and cement | 2016/C 378/08 |
| 040083-00-0404 | External thermal insulation composite systems (ETICS) with renderings | Decision (EU) 2020/1574 |
| 040089-00-0404 | ETICS with renderings for the use on timber frame buildings | 2017/C 118/04 |
| 040090-00-1201 | Factory-made boards and products formed by moulding of an expanded polylactic acid (EPLA) for thermal and/ or acoustical insulation | 2016/C 248/06 |
| 040138-01-1201 | In-situ formed loose fill thermal and/or acoustic insulation products made of vegetable fibres. | 2018/C 417/07 |
| 040287-00-0404 | Kits for external thermal insulation composite system (ETICS) with panels as thermal insulation product and discontinuous claddings as exterior skin | 2018/C 019/04 |
| 040288-00-1201 | Factory-made thermal and acoustic insulation made of polyester fibres | 2016/C 459/08 |
| 040313-00-1201 | In-situ formed loose fill thermal and/or acoustic insulation product made of granulated expanded cork | 2017/C 118/04 |
| 040369-00-1201 | Insulation made of loose-fill or compound granulated expanded cork | 2017/C 343/06 |
| 040394-00-1201 | Factory made cellular glass loose fill | 2018/C 049/04 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 040419-00-1201 | Thermal insulation board made of pressed rigid polyurethane foam | Decision (EU) 2020/1574 |
| 040427-00-0404 | Kits for external thermal insulation composite system (ETICS) with mortar as thermal insulation product and renderings or discontinuous claddings as exterior skin | Decision (EU) 2019/450 |
| 040456-00-1201 | In-situ formed loose fill thermal and/or acoustic insulation material made of animal fibres | 2017/C 343/06 |
| 040461-00-1201 | Thermal insulation product made of loose fill expanded perlite (EP) | 2018/C 281/04 |
| 040465-00-0404 | ETICS with renderings on mono-layer or multi-layer wall made of timber | Decision (EU) 2020/962 |
| 040635-00-1201 | Thermal and/or sound insulation based on bound expanded polystyrene bulk material | 2017/C 379/07 |
| 040643-00-1201 | Fiber reinforced silica aerogel thermal insulation | 2017/C 343/06 |
| 040650-00-1201 | Extruded polystyrene foam boards as load bearing layer and/or thermal insulation outside the waterproofing | 2017/C 435/07 |
| 040729-00-1201 | Thermal insulation made of loose mineral wool | Decision (EU) 2020/962 |
| 040773-00-1201 | Expanded polystyrene foam boards as load bearing layer and thermal insulation outside the waterproofing | 2018/C 417/07 |
| 040777-00-1201 | Cellular glass boards as load bearing layer and thermal insulation outside the waterproofing | 2017/C 435/07 |
| 040914-00-0404 | Veture kits – prefabricated units for external wall insulation and their fixing devices | Decision (EU) 2020/1574 |
| 041389-00-1201 | Boards made of agglomerated natural cork for thermal and acoustic insulation | Decision (EU) 2020/962 |
| 050001-00-0301 | Load bearing thermal insulating elements which form a thermal break between balconies and internal floors | 2018/C 090/04 |
| 050004-00-0301 | Spherical and cylindrical bearing with special sliding material made of UHMWPE (ultra high molecular weight polyethylene) | 2018/C 090/04 |
| 050009-00-0301 | Spherical and cylindrical bearing with special sliding material made of fluoropolymer | 2017/C 118/04 |
| 050013-00-0301 | Spherical and cylindrical bearing with special sliding material made of filled PTFE with solid lubricant and reinforcing fibres | 2017/C 435/07 |
| 050019-00-0301 | Dowels for structural joints under static and quasi-static loading | Decision (EU) 2020/1574 |
| 060001-00-0802 | (Ultra high molecular weight polyethylene) Chimney kit with clay/ceramic flue liner with classification T400 (minimum) N1 W3 Gxx | 2016/C 248/06 |
| 060003-00-0802 | Chimney kit with clay/ceramic flue liner and with specific outer wall with classification T 400 (minimum) N1 W 3 Gxx | 2016/C 248/06 |
| 060008-00-0802 | Chimney kit with clay/ceramic flue liner with classification T400 (minimum) N1/P1 W 3 Gxx and with different outer walls and possible change of outer wall | 2016/C 459/08 |
| 060012-00-0802 | Kit consisting of chimney flue liner, made of glass fibres, mineral and organic substances, and ancillaries | Decision (EU) 2019/450 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 070001-01-0504 | Gypsum plasterboard for load bearing applications | 2016/C 459/08 |
| 070002-00-0505 | Glass fibre joint tape for gypsum plasterboards | 2017/C 010/02 |
| 080001-00-0403 | Geocomposite for drainage system | 2018/C 281/04 |
| 080002-00-0102 | Non-reinforcing hexagonal geogrid for the stabilization of unbound granular layers by way of interlock with the aggregate | 2016/C 248/06 |
| 090001-00-0404 | Pre-fabricated compressed mineral wool boards with organic or inorganic finish and with specified fastening system | 2015/C 226/05 |
| 090017-00-0404 | Point supported vertical glazing | 2016/C 248/06 |
| 090019-00-0404 | Kits for ventilated external wall claddings of lightweight boards on subframe with rendering applied in situ with or without thermal insulation | 2018/C 019/04 |
| 090020-00-0404 | Kits for external wall claddings made of agglomerated stone | 2017/C 118/04 |
| 090034-00-0404 | Kit composed by subframe and fixings for fastening cladding and external wall elements | 2017/C 343/06 |
| 090035-00-0404 | Insulated glass unit with structural sealant punctually anchored | 2017/C 379/07 |
| 090058-00-0404 | Ventilated external wall cladding kit comprising a metallic honeycomb panel and its associated fixings | 2016/C 459/08 |
| 090062-00-0404 | Kits for external wall claddings mechanically fixed | 2018/C 417/07 |
| 090101-00-0404 | Cruciform glazing support to be used in curtain walls | 2018/C 417/07 |
| 090119-00-0404 | Kits for external wall cladding of mineral boards with renderings applied in situ | Decision (EU) 2019/450 |
| 090120-00-0404 | Kits for non-load bearing mineral board external wall systems | Decision (EU) 2019/450 |
| 120001-01-0106 | Microprismatic retro-reflective sheetings | 2016/C 459/08 |
| 120003-00-0106 | Steel lighting columns | 2015/C 378/02 |
| 120011-00-0107 | Flexible plug expansion joints for road bridges with flexible filling based on a synthetic polymer as binder | 2017/C 435/07 |
| 120093-00-0107 | Flexible asphaltic plug expansion joints for road bridges | Decision (EU) 2020/1574 |
| 120109-00-0107 | Nosing expansion joint for road bridges | Decision (EU) 2020/1574 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 120110-00-0107 | Mat expansion joint for road bridges | Decision (EU) 2020/1574 |
| 120111-00-0107 | Cantilever expansion joints for road bridges | Decision (EU) 2020/1574 |
| 120112-00-0107 | Supported expansion joints for road bridges | Decision (EU) 2020/1574 |
| 120113-00-0107 | Modular expansion joints for road bridges | Decision (EU) 2020/1574 |
| 130002-00-0304 | Solid wood slab element - element of dowel jointed timber boards to be used as a structural element in buildings | 2015/C 378/02 |
| 130005-00-0304 | Solid wood slab element to be used as a structural element in buildings | 2015/C 226/05 |
| 130010-01-0304 | Glued laminated timber made of hardwood – Structural laminated veneer lumber made of beech | 2018/C 417/07 |
| 130011-00-0304 | Prefabricated wood slab element made of mechanically jointed square-sawn timber members for use as structural element in buildings | 2016/C 248/06 |
| 130012-00-0304 | Strength graded structural timber - square edged logs with wane - chestnut | 2015/C 226/05 |
| 130013-00-0304 | Solid wood slab element to be used as a structural element in buildings - element of timber boards jointed by dovetail connections | 2016/C 248/06 |
| 130019-00-0603 | Dowel-type fasteners with resin coating | 2017/C 118/04 |
| 130022-00-0304 | Monolithic or laminated beam and wall logs made of timber | 2015/C 378/02 |
| 130031-00-0304 | Metal Web Beams and Columns | Decision (EU) 2019/450 |
| 130033-00-0603 | Nails and screws for use in nailing plates in timber structures | 2015/C 226/05 |
| 130082-00-0603 | Façade fixing system – plastic bracket for fixing timber or wood based elements to the substructure | Decision (EU) 2019/450 |
| 130087-00-0204 | Modular construction system | 2017/C 435/07 |
| 130089-00-0304 | Structural wet and/ or cold glued finger jointed solid timber | 2018/C 090/04 |
| 130090-00-0303 | Wood-concrete composite slab with dowel-type fasteners | 2018/C 019/04 |
| 130118-01-0603 | Screws and threaded rods for use in timber constructions | Decision (EU) 2020/962 |
| 130166-00-0304 | Strength graded structural timber - Steam cured solid timber with rectangular cross section which may be finger jointed or not - softwood | 2017/C 118/04 |
| 130167-00-0304 | Strength graded structural timber – Square edged logs with wane – Softwood | 2016/C 378/08 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 130186-00-0603 | Three dimensional nailing plates | Decision (EU) 2020/962 |
| 130191-00-0304 | Prefabricated wood slab element made of jointed cross laminated log elements to be used as a structural element in buildings | 2018/C 228/03 |
| 130196-00-0304 | Solid wood boards for flatwise structural use with overlapping edge profiles | 2018/C 417/07 |
| 130197-00-0304 | Glued laminated timber made of steam-cured solid timber with rectangular cross section – Softwood | 2017/C 343/06 |
| 130287-00-0603 | Profiled aluminium nail for use in timber structures | Decision (EU) 2020/962 |
| 130308-00-0304 | Structural composite lumber product: Laminated Strand Lumber (LSL) | Decision (EU) 2020/962 |
| 130324-00-0603 | Inserts for use in timber constructions | 2018/C 417/07 |
| 130336-00-0603 | Point connector – Dovetail made of plywood for cross laminated timber | Decision (EU) 2020/962 |
| 130367-00-0304 | Composite wood-based beams and columns | Decision (EU) 2020/962 |
| 140015-00-0304 | Walls, roofs and ceilings made of OSB-panels which are glued together on their surfaces | 2018/C 090/04 |
| 140022-00-0304 | Pre-fabricated wood-based loadbearing stressed skin panels | Decision (EU) 2020/1574 |
| 150001-00-0301 | Calcium sulphoaluminate based cement | 2017/C 118/04 |
| 150002-00-0301 | Calcium aluminate based refractory cement | 2017/C 343/06 |
| 150003-00-0301 | High strength cement | 2016/C 255/06 |
| 150004-00-0301 | Rapid hardening sulfate resistant calcium sulphoaluminate based cement | 2017/C 343/06 |
| 150007-00-0301 | Portland-pozzolana cement for use in tropical conditions | 2017/C 183/03 |
| 150008-00-0301 | Rapid setting cement | 2017/C 343/06 |
| 150009-00-0301 | Blast Furnace Cement CEM III/A with assessment of sulfate resistance (SR) and optional with low effective alkali content (LA) and/or low heat of hydration (LH) | 2017/C 379/07 |
| 160003-00-0301 | Double headed studs for the increase of punching shear resistance of flat slabs or footings and ground slabs | 2018/C 228/03 |
| 160004-00-0301 | Post-tensioning systems for prestressing of structures | 2017/C 435/07 |
| 160012-00-0301 | Headed reinforcement steel bars | 2018/C 090/04 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 160027-00-0301 | Special filling products for post-tensioning kits | 2017/C 435/07 |
| 160055-00-0301 | Lattice girders for the increase of punching shear resistance of flat slabs or footings and ground slabs | Decision (EU) 2020/962 |
| 170005-00-0305 | Re-cycled clay masonry units | Decision (EU) 2020/1574 |
| 170008-00-0604 | Bed joint reinforcement for structural use | 2018/C 417/07 |
| 170011-00-0305 | Insulating building element for masonry walls | Decision (EU) 2020/962 |
| 180003-00-0704 | Gully tops and manhole tops made of the polyamide (PA) for external vehicular and pedestrian areas | 2018/C 370/05 |
| 180008-00-0704 | Trapped gully - removable - mechanical closure | 2016/C 378/08 |
| 180018-00-0704 | Flexible couplings for gravity and pressure sewerage and drainage pipes | 2018/C 019/04 |
| 180022-00-0704 | Prefabricated plastic fitting made from recycled waste plastics and designed for drainage of land and civil engineering | 2018/C 417/07 |
| 180023-00-0704 | Vertical centrifugal storm water flow regulator | Decision (EU) 2020/962 |
| 190002-00-0502 | Dry floating flooring kit based on prefabricated interlocked units made of ceramic tiles and rubber mates | 2016/C 172/03 |
| 190005-00-0402 | Terrace decking kit | 2017/C 343/06 |
| 200001-00-0602 | Prefabricated steel and stainless steel wire ropes with end connectors | 2017/C 118/04 |
| 200002-00-0602 | Tension Rod System | 2016/C 248/06 |
| 200005-00-0103 | Structural steel piles with hollow sections and rigid splices | 2015/C 226/05 |
| 200012-00-0401 | Spacer Kits for Built-up Metal Roof and Wall Cladding | 2017/C 118/04 |
| 200014-01-0103 | Pile Joints and Rock shoes for concrete piles | 2018/C 370/05 |
| 200017-00-0302 | Hot rolled products and structural components made of steel grades Q235B, Q235D, Q345B and Q345D | 2016/C 172/03 |
| 200019-00-0102 | Hexagonal Woven Mesh Gabion Boxes and Mattresses | 2015/C 378/02 |
| 200020-00-0102 | Weldmesh Gabion Boxes and Mattresses | 2017/C 183/03 |
| 200022-00-0302 | Thermo-mechanically rolled long steel products made of weldable fine grain structural steel of special steel grades | 2016/C 172/03 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 200026-00-0102 | Steel mesh systems for reinforced fill | 2016/C 248/06 |
| 200032-00-0602 | Prefabricated tension rod systems with special end connectors | 2017/C 118/04 |
| 200033-00-0602 | Nailed shear connector | 2016/C 459/08 |
| 200035-00-0302 | Roof and wall systems with hidden fastenings | 2017/C 118/04 |
| 200036-00-0103 | Kit for micropiles – Kit with hollow bars for self-drilling micropiles | 2017/C 118/04 |
| 200039-00-0102 | Hexagonal woven gabion boxes and mattresses with zinc coatings | 2016/C 248/06 |
| 200043-01-0103 | Pile pipes made of ductile iron | 2017/C 435/07 |
| 200050-02-0102 | Gabion boxes, mattresses and sack gabions made of hexagonal regular twisted mesh, metallic pre-coated, with or without additional organic coating | Decision (EU) 2020/962 |
| 200059-00-0302 | Steel components for pallet racking systems | 2018/C 417/07 |
| 200086-00-0602 | Wire ring connection products | 2017/C 379/07 |
| 200089-00-0302 | In-situ concrete slab permanent joint former | 2018/C 417/07 |
| 210004-00-0805 | Modular element for building services | 2017/C 118/04 |
| 210005-00-0505 | Internal partition kits for use as non-loadbearing walls | Decision (EU) 2019/896 |
| 210012-00-0504 | Gypsum elements for internal wall finishes | 2018/C 417/07 |
| 210020-00-0402 | Factory made self-supporting composite PUR/PIR foam insulated metal sheet for roofing, external cladding and internal lining | 2018/C 417/07 |
| 210024-00-0504 | Cement-bonded board | 2018/C 049/04 |
| 210046-00-1201 | Thin metal composite sheet | Decision (EU) 2019/896 |
| 220006-00-0402 | Roofing slates made of polypropylene, limestone and fillers | 2017/C 118/04 |
| 220007-00-0402 | Fully supported copper alloy sheet and strip for roofing, external cladding and internal lining | 2016/C 054/14 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 220008-00-0402 | Eaves profiles for terraces and balconies | 2016/C 248/06 |
| 220010-01-0402 | Flat plastic roofing sheets made of recycled plastic for self-supporting and/or fully supported discontinuous roofing and/or external cladding | Decision (EU) 2020/962 |
| 220013-01-0401 | Self–supporting ridgelight | 2017/C 343/06 |
| 220018-00-0401 | Decentralized energy efficient low-pressure ventilations unit with alternating flow and heat recovery | 2017/C 379/07 |
| 220021-00-0402 | Tubular daylighting devices (TDD) | 2015/C 378/02 |
| 220022-00-0401 | Polycarbonate snow stopper for roof | 2017/C 010/02 |
| 220025-00-0401 | Cantilevered Structural horizontal glazing (structural glass canopy/roof) | 2016/C 172/03 |
| 220062-00-0401 | Rooflight with bonded or mechanically fastened cover glass | Decision (EU) 2020/962 |
| 220069-00-0402 | Flat and profiled (with a pattern) plastic roofing sheets made of recycled material for fully supported discontinuous roofing | 2017/C 435/07 |
| 220089-00-0401 | Self-Supporting translucent roof kits with covering made of plastic sheets | Decision (EU) 2019/896 |
| 220116-00-0401 | Fixed fire-resistant roof window | Decision (EU) 2020/962 |
| 230004-00-0106 | Wire ring mesh panels | 2016/C 172/03 |
| 230005-00-0106 | Wire rope net panels | 2016/C 172/03 |
| 230008-00-0106 | Double twisted steel wire mesh reinforced or not with ropes | 2016/C 172/03 |
| 230011-00-0106 | Road marking products | 2017/C 118/04 |
| 230012-01-0105 | Additives for asphalt production - additives from bitumen granules made from recycled bituminous roofing felt | 2018/C 281/04 |
| 230025-00-0106 | Flexible facing systems for slope stabilization and rock protection | 2016/C 378/08 |
| 260001-00-0303 | Structural sections made from fibre reinforced polymers (FRP/Glassfiber Composites) | 2017/C 379/07 |
| 260002-00-0301 | Alkali resistant glass fibres containing zirconium dioxide for the use in concrete | 2017/C 343/06 |
| 260006-00-0301 | Polymeric concrete addition | 2016/C 172/03 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 260007-00-0301 | Type I addition for concrete, mortar and screed materials – Aqueous solution | 2017/C 010/02 |
| 260009-00-0301 | Processed bottom ash from municipal solid waste incinerators as type II addition for production of concrete, mortar and grout | 2018/C 370/05 |
| 260014-00-0301 | Calcined layer silicate based type II addition | Decision (EU) 2019/450 |
| 260017-00-0301 | Elastic micro hollow spheres as concrete admixture | Decision (EU) 2019/896 |
| 260020-00-0301 | Calcium carbonate fine as active addition with catalytic binding performance for concrete | Decision (EU) 2020/1574 |
| 260035-00-0301 | Natural calcined pozzolana as type II addition | 2018/C 228/03 |
| 280001-00-0704 | Preassembled line unit used for drainage of infiltration | 2015/C 226/05 |
| 280015-00-0701 Previously referred as 290001-00-0701 |
Kit for the transport of cold and hot water inside buildings | 2016/C 172/03 |
| 320001-00-0605 | Joint sealing tape on the basis of a pre-compressed flexible polyurethane foam for sealing around windows and joints in building facades | 2018/C 417/07 |
| 320002-02-0605 | Coated metal water stop sheet for construction and controlled crack joints in waterproof concrete | 2016/C 459/08 |
| 320008-01-0605 | Swellable joint sealing tape on the basis of swellable materials for construction in watertight concrete | 2018/C 417/07 |
| 330001-00-0602 | Expanding Structural Bolting Assemblies for Blind Fastening | 2017/C 118/04 |
| 330008-02-0601 | Anchor channels | 2016/C 248/06 |
| 330011-00-0601 | Adjustable concrete screws | 2015/C 226/05 |
| 330012-00-0601 | Cast-in anchor with internal threaded socket | 2016/C 172/03 |
| 330014-00-0601 | Metal expansion fastener for use in autoclaved aerated concrete | 2018/C 049/04 |
| 330030-00-0601 | Fastener of external wall claddings | 2018/C 417/07 |
| 330046-00-0602 | Fastening Screws for Metal Members and Sheeting | 2018/C 049/04 |
| 330046-01-0602 | Fastening Screws for Metal Members and Sheeting | 2018/C 049/04 |
| 330047-01-0602 | Fastening Screws for Sandwich Panels | 2017/C 118/04 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 330075-01-0601 | Elevator Lifting Device | 2018/C 417/07 |
| 330076-00-0604 | Metal injection anchors for use in masonry | 2017/C 435/07 |
| 330079-00-0602 | Floor Fixing Assemblies for Use in Checker Plate or Open Bar Grating | 2016/C 248/06 |
| 330080-00-0602 | High Slip Resistance Clamp (HSR) Assembly | 2016/C 248/06 |
| 330083-02-0601 | Powder-actuated fastener for multiple use in concrete for non-structural applications | 2018/C 370/05 |
| 330084-00-0601 | Steel plate with cast-in anchor | 2016/C 378/08 |
| 330087-00-0601 | Systems for post-installed rebar connections with mortar | 2018/C 370/05 |
| 330153-00-0602 | Cartridge fired pin for connections of thin gauge steel members and sheeting | 2015/C 378/02 |
| 330155-00-0602 | Self adjustable clamp assemblies | 2016/C 459/08 |
| 330196-00-0604 | Plastic anchors for fixing of ETICS with rendering | 2016/C 459/08 |
| 330196-01-0604 Previously referred as 330335-00-0604 |
Plastic anchors made of virgin or non-virgin material for fixing of ETICS with rendering | 2017/C 379/07 |
| 330232-00-0601 | Mechanical fasteners for use in concrete | 2016/C 459/08 |
| 330284-00-0604 | Plastic anchors for redundant non-structural systems in concrete and masonry | Decision (EU) 20 |
| 330340-00-0606 | Factory made structural anchor for attaching personal fall protection equipment, designed to be permanently and fully bonded to a multi-layered roof waterproofing system | 2018/C 417/07 |
| 330389-00-0601 | Point connector made of glass fibre reinforced polymer for sandwich walls | 2017/C 183/03 |
| 330499-01-0601 | Bonded fasteners for use in concrete | Decision (EU) 2020/1574 |
| 330667-00-0602 | Hot-rolled mounting channel | 2017/C 118/04 |
| 330747-00-0601 | Fasteners for use in concrete in redundant for non-structural systems | 2018/C 281/04 |
| 330924-00-0601 | Cast-in anchor bolt of ribbed reinforcing steel | 2018/C 049/04 |
| 330965-00-0601 | Powder actuated fastener for the fixing of ETICS in concrete | 2017/C 183/03 |
| EAD Number | EAD Title | OJEU citation |
|---|---|---|
| 331072-00-0601 | Anchor devices for fastening personal fall protection systems to concrete structures | 2018/C 417/07 |
| 331433-00-0601 | Injected anchor for thermal insulation boards | Decision (EU) 2020/1574 |
| 331852-00-0102 | Spiral Cable Anchor | 2018/C 281/04 |
| 331924-00-0602 | Decking Fixing Assemblies | Decision (EU) 2019/896 |
| 332001-00-0602 | Clamping system for connection of precast concrete members | Decision (EU) 2020/962 |
| 332277-00-0601 | Fastener for push-pull props for precast wall/column elements | Decision (EU) 2020/1574 |
| 340002-00-0204 | Panels of steel wires with incorporated thermal insulation for a whole structure | 2016/C 248/06 |
| 340006-00-0506 | Prefabricated Stair Kits | 2016/C 172/03 |
| 340020-00-0106 | Flexible kits for retaining debris flows and shallow landslides/open slope debris flows | 2016/C 378/08 |
| 340025-00-0403 | Substructure kit for heated buildings. | 2016/C 172/03 |
| 340037-00-0204 | Light weight steel/wood bearing roof elements | 2016/C 172/03 |
| 340059-00-0106 | Falling rock protection kits | 2018/C 417/07 |
| 340210-00-0104 | SRP (Steel Reinforced Polymer) kit made of steel micro-wires, fiberglass mesh and epoxy adhesive | 2018/C 417/07 |
| 340275-00-0104 | Externally-bonded composite systems with inorganic matrix for strengthening of concrete and masonry structures | Decision (EU) 2020/962 |
| 340308-00-0203 | Timber building kits | Decision (EU) 2020/1574 |
| 340392-00-0104 | CRM (Composite Reinforced Mortar) Systems for strengthening concrete and masonry structures | Decision (EU) 2020/1574 |
| 350003-00-1109 | Kit for fire resistant service ducts consisting of pre-fabricated connection pieces (made of mechanically pre-coated steel sheet) and accessories | 2016/C 172/03 |
| 350005-00-1104 | Intumescent products for fire sealing and fire stopping purposes | 2015/C 378/02 |
| 350022-01-1107 | Kit for closure system for conveyor systems | 2018/C 049/04 |
| 350134-00-1104 | Fire proof water trap with intumescent fire seal (combined with a stainless steel floor gully penetration) | 2016/C 248/06 |
| 350140-00-1106 | Renderings and rendering kits intended for fire resistant applications | 2017/C 435/07 |
| 350141-00-1106 | Linear joint and gap seals | 2017/C 435/07 |
| 350142-00-1106 | Fire protective board, slab and mat products and kits | 2017/C 435/07 |
| 350402-00-1106 | Reactive coatings for fire protection of steel elements | 2017/C 435/07 |
| 350454-00-1104 | Fire stopping and fire sealing products - Penetration seals | 2017/C 435/07 |
| 350865-00-1106 | Fire retardant products | Decision (EU) 2020/1574 |
| 360001-00-0803 | Ventilation system made of mineral wool covered with film on outside and inside | 2018/C 049/04 |
| 360005-00-0604 | Cavity trays | 2016/C 459/08 |
European Technical Approval Guidelines (ETAGs)
The following list of ETAGs recognised as ‘pre-Exit’ EADs does not include references to documents that have been superseded by EADs. Those particular documents can be found in the full list of ETAGs, accessible on the EOTA website.
| ETAG Number | ETAG Title | Date of EC endorsement |
|---|---|---|
| ETAG 002 | Structural Sealant Glazing Systems Part 1: Supported and Unsupported Systems |
27-06-2013 |
| ETAG 002 | Structural Sealant Glazing Systems Part 2 : Coated Aluminium Systems |
16-01-2002 |
| ETAG 002 | Structural Sealant Glazing Systems Part 3 : Systems incorporating profiles with thermal barrier |
25-05-2002 |
| ETAG 009 | Non load-bearing permanent shuttering Kits/Systems based on Hollow Blocks or Panels of insulating materials or concrete | 25-05-2002 |
| ETAG 016 will only be developed into an EAD upon ETA request by manufacturer |
Composite Light Weight Panels Part 1: General *) ETAG 016 is not applicable for the assessment of Kits/Systems to which the Panel might belong |
09-02-2004 |
| ETAG 016 will only be developed into an EAD upon ETA request by manufacturer |
Composite Light Weight Panels Part 2: Specific aspects related to self-supporting Composite Lightweight Panels for use in Roofs |
17-02-2004 |
| ETAG 016 will only be developed into an EAD upon ETA request by manufacturer |
Composite Light Weight Panels Part 3: Specific aspects related to self-supporting Composite Lightweight Panels for use in External Walls and Claddings |
02-03-2004 |
| ETAG 016 will only be developed into an EAD upon ETA request by manufacturer |
Composite Light Weight Panels Part 4: Specific aspects related to self-supporting Composite Lightweight Panels for use in Internal Walls and Ceilings |
02-03-2004 |
| ETAG 021 will only be developed into an EAD upon ETA request by manufacturer |
Cold Storage Premises Kits Part 1: Cold Storage Room Kits + Annexes Part 2: Cold Storage Building Envelope and Building Kits |
16-11-2005 |
| ETAG 023 will only be developed into an EAD upon ETA request by manufacturer |
Prefabricated Building Units | 19-09-2006 |
| ETAG 024 will only be developed into an EAD upon ETA request by manufacturer |
Concrete Frame Building Kits | 28-07-2006 |
| ETAG 025 will only be developed into an EAD upon ETA request by manufacturer |
Metal Frame Building Kits | 28-07-2006 |
| ETAG 026 | Fire Stopping and Fire Sealing Products Part 4: Reactive and Mechanical Air Transfer Grilles (Fire resistant and Cold Smoke Control Fire Resistant Types) |
14-05-2012 |
| ETAG 026 | Fire Stopping and Fire Sealing Products Part 5 : Cavity Barriers |
26-09-2011 |
| ETAG 031 will only be developed into an EAD upon ETA request by manufacturer |
Inverted Roofs Insulation Kits Part 1: General Part 2: Insulation with protective Finish |
14-12-2010 |
| ETAG 033 will only be developed into an EAD upon ETA request by manufacturer |
Liquid applied Bridge Deck waterproofing Kits | 25-09-2010 |
| ETAG 035 will only be developed into an EAD upon ETA request by manufacturer |
Ultra thin layer Asphalt Concrete | 12-05-2011 |
End note
The development of these pre-Exit EADs was funded in part by the European Commission.
Updates to this page
Published 2 December 2021